Craftsman 10 Single Bevel Sliding Compound Miter S

CRAFTSMAN 2. 12. 37 - 1. IN. SLIDING MITER SAW OPERATOR'S MANUAL Pdf Download. Maintenance all its Safety Rules and Parts List Operating instructions Sears Parts & Customer Help Line For Technical Support Repair Center 1- 8. Sears, Roebuck and Co., Hoffman Estates, IL 6. USA Visit our Craftsman website: www. Part No. 1. 37. 21.

FULL WARRANTY ON CRAFTSMAN TOOL If this Craftsman tool fails due to a defect in material or workmanship within one year from the date of purchase, CALL 1- 8. MY- HOME(. If this tool is used for commercial or rental purposes, this warranty will apply for only ninety days from the date of purchase.

NOTE: Glasses or goggles not in GENERAL SAFETY i. NSTRUCTi. ONS compliance with ANSI Z8. Read and understand all the instructions below injury. WEAR A FACE MASK OR DUST MASK, Sawing instructions are not meant to cover every possible operation produces dust. I. IMPORTANT: DO NOT USE THIN KERF BLADES. MOTOR is overloaded - overloading can occur if thickness of insulation between you and tool's electrical you feed too rapidly or make too many start/stops system. RECOMMENDED ACCESSORIES Supplied Not supplied ...

Download craftsman 10 single bevel sliding compound miter saw 21237 user. Shop for a Craftsman 10' Single Bevel Sliding Compound Miter Saw (21237). 10' single bevel sliding compound miter saw. Craftsman - DM3050RC - 12 INCH DUAL BEVEL.

Follow instructions that accompany accessories. Use of improper accessories cause hazards.

Craftsman 10 Single Bevel Sliding Compound Miter Saw. Single Bevel Sliding Compound Miter Saw 21237. Craftsman 10 Single Bevel Sliding Compound.

Separate all parts from the packing material. WOODWORKING TERMS BASE - Supports the table, holds accessories and allows for workbench or leg set mounting. CUTTING HEAD (FIG. C) Estimated Assembly Time: 5 - 1. Raising . Push down slightly on the switch handle (I). Pull out the stop latch knob (2). To avoid injury, do not connect this miter saw to the 3.

Craftsman 10 Single Bevel Sliding Compound. 15-Amp 10-inch Single Bevel Compound Miter Saw with.

10' Single Bevel Sliding Compound Miter Saw 21237. Craftsman 10' Single Bevel Sliding Compound. Single Bevel Sliding Compound Miter Saw (21237). A Craftsman 10' Sliding Compound Miter Saw Gets the. Craftsman 10 Single Bevel Sliding Compound Miter Saw 21237.

NSTALLi. NG THE HOLD- DOWN CLAMP 1. To remove, loosen and remove the six screws (1) (FIG. E and E- l) on the table insert (2) with a Phillips screwdriver and remove the insert. Place the hold=down clamp assembly (1) in one of the mounting holes (2).

Mounting instructions 4. Rotate the cover plate (3) towards the rear of the tool 1. For stationary use, place the saw in the desired to expose the arbor bolt (4). Place the blade wrench over the arbor bolt. H, I, J) 1 . To turn laser on, press on/off rocker switch (1) to Unplug the miter saw before changing/installing . To turn off laser, press on/off rocker switch (1) to I. P The sliding compound miter saw scale can be easily read, showing miter angles from 0 .

The miter saw table has nine of the most common angle setttings with positive stops at 0 . Do not force a tool or attachment cut off. Otherwise, it could get wedged against the to do a job it was not designed to do. Use a different blade and thrown violently. BASIC SAW OPERATIONS BODY AND HAND POSITION (FIG. Proper For your convenience, your saw has a blade brake. Never rely on it to operating the miter saw will make cutting easier and replace the proper use of the guard on your saw.

SLIDING CARRIAGE SYSTEM (FIG. The table To reduce the risk of injury, return carriage to the is now locked at the desired angle. NOTE: T hesawcomes witha 3. Push the bevel detent stop pin (2) in toward the front To avoid injury: of the machine. AUXILIARY WOOD FENCE (FIG.

CC) CUTTING BOWED MATERIAL (FIG. Z) When making multiple or repetitive cuts that result in A bowed workpiece must be positioned against the fence and secured with a cramping devise before cutting cut- off pieces of one inch or less, it is possible for the saw blade to catch the out=off piece and throw it out of as shown. CUTTING BASE MOLDING (FIG. EE Base moldings and many other moldings can be cut on a compound miter saw. The setup of the saw depends on molding characteristics and applications, as shown. Perform practice cuts on scrap material.

To achieve best results: I. CROWN MOLDING CHART Compound Miter Saw Miter and Bevel Angle Settings Wall to Crown Molding Angle 5. They could DANGER make the plastic . Never put lubricants on the blade while it is .

TROU BLESHOOTING GUIDE - MOTOR PROBLEM PROBLEM CAUSE SUGGESTED CORRECTIVE ACTION Brake does not I. Motor brushes not sealed or lightly Inspect/clean/replace brushes. MODEL. O 1. 37. 2.